Assembly Guides

This guide will contain instructions for building the extruder for the Positron V3.2.

This guide will contain instructions for building the Z drive for the Positron V3.2.

This guide uses the official StealthBurner Assembly Manual VERSION 2023-07-07 The kits supported are the Voron V2.4 and Trident Revision C which include the 2 piece Stealthburner PCBs based on the Hartk design

This guide will contain instructions for building the bed V holder for the Positron V3.2.

This guide will contain instructions for building the base plate (part 2) for the Positron V3.2.

This guide will contain instructions for building the base plate (part 1) for the Positron V3.2.

This guide will contain instructions for folding the Positron V3.2.

This guide will walk you through the assembly of the the Nevermore filter. This is highly recommended for anyone printing using ABS or ASA filaments. For more information check out - Nevermore Activated Carbon Filters - Micro Edition Also check out the video guide by Maple Leaf Makers - Nevermore Carbon Filter We would thank the Voron Design team for all of their hard work and contributions to the 3D printing community. GPLv3 License Attributions: https://github.com/nevermore3d/Nevermore_Micro For more information and support: https://docs.ldomotors.com

THIS MOD NO LONGER REQUIRED for V2.4 Rev. C - the kit includes the Stealthburner PCBs and works with the stock parts. This guide will step you through the installation of the mod for the Steathburner + Clockwork 2 to use the LDO Clockwork 1 Toolhead PCB. The mod is improvement over version 1 that fixes the umbilical wire from hitting the Z cable chain ( Previous Guide ) . This mod will replace parts from official Stealthburner + Clockwork 2 GitHub repo . We would thank the Voron Design team for all of their hard work and contributions to the 3D printing community. GPLv3 License Attributions: https://github.com/VoronDesign/Voron-Stealthburner For more information and support: https://vorondesign.com https://discord.gg/voron https://docs.ldomotors.com

This guide will walk you through common firmware configurations for your 3D printers. There are two major steps covered in this guide that will need to be completed in order: Flashing the Leviatan with the Katapult Bootloader The USB interface should be used for the Katapult bootloader for both USB or CAN Klipper configuration. The UART interface should be used for the Katapult bootloader for UART Klipper configuration. Flashing the Leviatan with the Klipper Firmware USB interface is the recommended configuration for most situations. CAN interface is supported, if you are using CANBus UART interface can be used when USB ports aren't available such as with Raspberry Pi Zero 2W. This are the recommended configurations however Leviathan is very flexible, so not all options are covered by this guide. Important Links: Leviathan GitHub Repo - https://github.com/MotorDynamicsLab/Leviathan

This guide will walk you through common firmware configurations for your 3D printers. Leviathan boards ship out already flashed with USB firmware. Run ls /dev/serial/by-id/* to confirn you have a klipper ID. If you need to update firmware or use other ways of connection, there are two major steps covered in this guide that will need to be completed in order: Flashing the Leviatan with the Katapult Bootloader The USB interface should be used for the Katapult bootloader for both USB or CAN Klipper configuration. The UART interface should be used for the Katapult bootloader for UART Klipper configuration. Flashing the Leviatan with the Klipper Firmware USB interface is the recommended configuration for most situations. CAN interface is supported, if you are using CANBus UART interface can be used when USB ports aren't available such as with Raspberry Pi Zero 2W. This are the recommended configurations however Leviathan is very flexible, so not all options are covered by this guide. Important Links: Leviathan GitHub Repo - https://github.com/MotorDynamicsLab/Leviathan

This guide walks your through the assembly of the bowden extruder for the Positron V3.2. We also recommend you checking wiki.positron3d.com during the whole build as there are many helpful information.